Søk i nettsamfunnet

Hei, Har prøvd å få ut startmotoren på en 2007 Defender Puma, og står litt fast. De to festeskruene er tatt ut, og motoren er løs. Jeg får lirket den et stykke ut, men ikke nok til at jeg kommer til skruene til kabelskoene. Kablene er enten for korte, eller så henger de fast i noe jeg ikke kan se på baksiden, eller så gjør jeg dette på helt feil måte... I følge verksted-manualen skal egentlig kablene skrus løs før man løsner festeskruene, men jeg forstår ikke hvordan man skal komme til. Noen som har gjort dette før som kan gi meg en pekepinn? -Richard

Har en D3 2006 som har fungert uten noen problem. Står normalt i garasje, men her en kveld stod den selvfølgelig ute og i bakke å da startet den ikke. Når jeg vrir om nøkkel hører jeg bare klikking. Ingen feilmeldinger i display. Nytt batteri har den også. Noen som har ide om hvor jeg kan begynne å sjekke etter feil eller har egne liknende erfaringer Tok en diagnose og det kom opp ufattelig mange feil. Ingen lot seg slette Som dere ser under så er listen lang som et vondt år VIN SALLAAA146A352733 Model L319 - Discovery 3 2006 Vehicle scanned on 17. feb. 2018 11:35:45 IIDControl 2.9.4.5 Android - IIDTool BT V3.0 B2481 Auxilary Heater B1A00-49 (50) Control module - System internal failure - internal electronic failure *Test Not Completed *Test Not Completed This Monitoring Cycle B1D22-11 (50) Water temperature sensor circuit - General electrical failure - circuit short to ground *Test Not Completed *Test Not Completed This Monitoring Cycle B1D22-15 (50) Water temperature sensor circuit - General electrical failure - circuit short to battery or open *Test Not Completed *Test Not Completed This Monitoring Cycle B1D23-13 (50) Overheat sensor circuit - General electrical failure - circuit open *Test Not Completed *Test Not Completed This Monitoring Cycle B1D24-11 (50) Glow plug circuit - General electrical failure - circuit short to ground *Test Not Completed *Test Not Completed This Monitoring Cycle B1D24-15 (50) Glow plug circuit - General electrical failure - circuit short to battery or open *Test Not Completed *Test Not Completed This Monitoring Cycle B1D25-11 (50) Dosing pump circuit - General electrical failure - circuit short to ground *Test Not Completed *Test Not Completed This Monitoring Cycle B1D25-15 (50) Dosing pump circuit - General electrical failure - circuit short to battery or open *Test Not Completed *Test Not Completed This Monitoring Cycle B1D26-11 (50) Combustion air fan circuit - General electrical failure - circuit short to ground *Test Not Completed *Test Not Completed This Monitoring Cycle B1D26-15 (50) Combustion air fan circuit - General electrical failure - circuit short to battery or open *Test Not Completed *Test Not Completed This Monitoring Cycle B1D26-93 (50) Combustion air fan circuit - Component failure - no operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1D26-92 (50) Combustion air fan circuit - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1D27-11 (50) Coolant pump circuit - General electrical failure - circuit short to ground *Test Not Completed *Test Not Completed This Monitoring Cycle B1D27-15 (50) Coolant pump circuit - General electrical failure - circuit short to battery or open *Test Not Completed *Test Not Completed This Monitoring Cycle B1D28-11 (50) Fuel pre-heater circuit - General electrical failure - circuit short to ground *Test Not Completed *Test Not Completed This Monitoring Cycle B1D28-15 (50) Fuel pre-heater circuit - General electrical failure - circuit short to battery or open *Test Not Completed *Test Not Completed This Monitoring Cycle B1A00-16 (50) Control module - General electrical failure - circuit voltage below threshold *Test Not Completed *Test Not Completed This Monitoring Cycle B1A00-17 (50) Control module - General electrical failure - circuit voltage above threshold *Test Not Completed *Test Not Completed This Monitoring Cycle U0073-08 (50) Control module communication bus off - General failure information - bus signal/message failure *Test Not Completed *Test Not Completed This Monitoring Cycle B1D34-68 (50) Heater in lock out mode - Algorithm based failure - event information *Test Not Completed *Test Not Completed This Monitoring Cycle U1A37-87 (50) Crash status telegram - Bus signal/message failure - missing a message *Test Not Completed *Test Not Completed This Monitoring Cycle U1A00-08 (50) Private bus circuit - General failure information - bus signal/message failure *Test Not Completed *Test Not Completed This Monitoring Cycle U1A03-95 (50) Vehicle configuration parameter - Component failure - incorrect assembly *Test Not Completed *Test Not Completed This Monitoring Cycle B1A00-43 (50) Control module - System internal failure - special memory failure *Test Not Completed *Test Not Completed This Monitoring Cycle U0164-87 (50) Lost communication with heating ventilation and air conditioning control module - Bus signal/message failure - missing a message *Test Not Completed *Test Not Completed This Monitoring Cycle B1D63-11 (50) External control relay - General electrical failure - circuit short to ground *Test Not Completed *Test Not Completed This Monitoring Cycle B1D63-15 (50) External control relay - General electrical failure - circuit short to battery or open *Test Not Completed *Test Not Completed This Monitoring Cycle U1A44-6C (50) Fuel level *Test Not Completed *Test Not Completed This Monitoring Cycle U3000-55 (50) Control module - System programming failure - is not configured *Test Not Completed *Test Not Completed This Monitoring Cycle Body Control B1A59-16 (50) Sensor 5 volt supply circuit - General electrical failure - circuit voltage below threshold *Test Not Completed *Test Not Completed This Monitoring Cycle B1A99-4C (50) Power on reset *Test Not Completed *Test Not Completed This Monitoring Cycle B1B00-42 (50) Electrically erasable programmable read only memory - bad checksum in flash - System internal failure - general memory failure *Test Not Completed *Test Not Completed This Monitoring Cycle B1B00-44 (50) Electrically erasable programmable read only memory - bad checksum in flash - System internal failure - data memory failure *Test Not Completed *Test Not Completed This Monitoring Cycle B1B00-45 (50) Electrically erasable programmable read only memory - bad checksum in flash - System internal failure - program memory failure *Test Not Completed *Test Not Completed This Monitoring Cycle B1B00-47 (50) Electrically erasable programmable read only memory - bad checksum in flash - System internal failure - watchdog/safety failure *Test Not Completed *Test Not Completed This Monitoring Cycle B1B01-46 (50) Key transponder - System internal failure - calibration/parameter memory failure *Test Not Completed *Test Not Completed This Monitoring Cycle B1B01-4A (50) Key transponder - System internal failure - incorrect component installed *Test Not Completed *Test Not Completed This Monitoring Cycle B1B01-4C (50) Key transponder *Test Not Completed *Test Not Completed This Monitoring Cycle B1B01-66 (50) Key transponder - Algorithm based failure - signal has too many transitions/events *Test Not Completed *Test Not Completed This Monitoring Cycle B1B01-87 (50) Key transponder - Bus signal/message failure - missing a message *Test Not Completed *Test Not Completed This Monitoring Cycle B1B02-28 (2F) Low frequency coil - General signal failure - signal bias level is out of range/zero adjustment failure ( at 221220 km ) *Test Failed *Test Failed This Monitoring Cycle *Confirmed *Test Failed Since Last Clear B1B03-53 (50) Antenna failure - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle B1B03-92 (50) Antenna failure - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1B03-96 (50) Antenna failure - Component failure - internal failure *Test Not Completed *Test Not Completed This Monitoring Cycle B1B04-53 (50) Transponder key 2 - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle B1B04-92 (50) Transponder key 2 - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1B05-53 (50) Transponder key 3 - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle B1B05-92 (50) Transponder key 3 - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1B06-53 (50) Transponder key 4 - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle B1B06-92 (50) Transponder key 4 - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1B07-53 (50) Transponder key 5 - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle B1B07-92 (50) Transponder key 5 - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1B08-53 (50) Transponder key 6 - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle B1B08-92 (50) Transponder key 6 - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1B09-53 (50) Transponder key 7 - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle B1B09-92 (50) Transponder key 7 - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1B10-53 (50) Transponder key 8 - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle B1B10-92 (50) Transponder key 8 - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1B11-53 (50) Transponder key 9 - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle B1B11-92 (50) Transponder key 9 - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1B12-53 (50) Transponder key 10 - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle B1B12-92 (50) Transponder key 10 - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1B13-53 (50) Transponder key 11 - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle B1B13-92 (50) Transponder key 11 - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1B14-53 (50) Transponder key 12 - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle B1B14-92 (50) Transponder key 12 - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1B15-53 (50) Transponder key 13 - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle B1B15-92 (50) Transponder key 13 - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1B16-53 (50) Transponder key 14 - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle B1B16-92 (50) Transponder key 14 - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1B17-53 (50) Transponder key 15 - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle B1B17-92 (50) Transponder key 15 - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1B18-53 (50) Transponder key 16 - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle B1B18-92 (50) Transponder key 16 - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1B19-53 (50) Transponder key 17 - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle B1B19-92 (50) Transponder key 17 - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1B20-53 (50) Transponder key 18 - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle B1B20-92 (50) Transponder key 18 - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1B21-53 (50) Transponder key 19 - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle B1B21-92 (50) Transponder key 19 - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1B22-53 (50) Transponder key 20 - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle B1B22-92 (50) Transponder key 20 - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1B23-53 (50) Transponder key 21 - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle B1B23-92 (50) Transponder key 21 - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1B24-53 (50) Transponder key 22 - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle B1B24-92 (50) Transponder key 22 - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1B25-53 (50) Transponder key 23 - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle B1B25-92 (50) Transponder key 23 - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle B1B26-53 (50) Transponder key 24 - System programming failure - deactivated *Test Not Completed *Test Not Completed This Monitoring Cycle Cell Phone U0029-68 (50) Vehicle communication bus A performance - Algorithm based failure - event information *Test Not Completed *Test Not Completed This Monitoring Cycle U0400-68 (50) Invalid data received (event diagnostic trouble code) - Algorithm based failure - event information *Test Not Completed *Test Not Completed This Monitoring Cycle Navigation B110E-25 (50) Tailgate double locking motor - General signal failure - signal shape/waveform failure *Test Not Completed *Test Not Completed This Monitoring Cycle B1110-25 (50) Air suspension delay power - General signal failure - signal shape/waveform failure *Test Not Completed *Test Not Completed This Monitoring Cycle B1A89-13 (50) Satellite antenna - General electrical failure - circuit open *Test Not Completed *Test Not Completed This Monitoring Cycle B1D62-87 (50) Sub-module 'B' - Bus signal/message failure - missing a message *Test Not Completed *Test Not Completed This Monitoring Cycle B1D62-49 (50) Sub-module 'B' - System internal failure - internal electronic failure *Test Not Completed *Test Not Completed This Monitoring Cycle Suspension C1A31-01 (50) Front left corner valve - General failure information - general electrical failure *Test Not Completed *Test Not Completed This Monitoring Cycle C1A32-01 (50) Front right corner valve - General failure information - general electrical failure *Test Not Completed *Test Not Completed This Monitoring Cycle C1A33-01 (50) Rear left corner valve - General failure information - general electrical failure *Test Not Completed *Test Not Completed This Monitoring Cycle C1A34-01 (50) Rear right corner valve - General failure information - general electrical failure *Test Not Completed *Test Not Completed This Monitoring Cycle C1A35-01 (50) Reservoir valve - General failure information - general electrical failure *Test Not Completed *Test Not Completed This Monitoring Cycle C1A37-01 (50) Front cross-link valve - General failure information - general electrical failure *Test Not Completed *Test Not Completed This Monitoring Cycle C1A38-01 (50) Rear cross-link valve - General failure information - general electrical failure *Test Not Completed *Test Not Completed This Monitoring Cycle C1A13-64 (50) Pressure does not decrease when venting gallery - Algorithm based failure - signal plausibility failure *Test Not Completed *Test Not Completed This Monitoring Cycle C1A36-01 (50) Exhaust valve - General failure information - general electrical failure *Test Not Completed *Test Not Completed This Monitoring Cycle C1A24-67 (50) No temperature increase when compressor requested - Algorithm based failure - signal is incorrect after the event *Test Not Completed *Test Not Completed This Monitoring Cycle C1A18-64 (50) Pressure increases too rapid when filling reservoir - Algorithm based failure - signal plausibility failure *Test Not Completed *Test Not Completed This Monitoring Cycle C1A24-64 (50) No temperature increase when compressor requested - Algorithm based failure - signal plausibility failure *Test Not Completed *Test Not Completed This Monitoring Cycle C1A27-14 (50) Compressor circuit - General electrical failure - circuit short to ground or open *Test Not Completed *Test Not Completed This Monitoring Cycle C1A29-92 (50) Switch activation too long - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle C1A30-64 (50) Both switches pressed at the same time - Algorithm based failure - signal plausibility failure *Test Not Completed *Test Not Completed This Monitoring Cycle C1A03-26 (50) Front left height sensor - General signal failure - signal rate of change is below the threshold *Test Not Completed *Test Not Completed This Monitoring Cycle C1131-92 (50) Air supply - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle C1A03-92 (50) Front left height sensor - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle C1A04-26 (50) Front right height sensor - General signal failure - signal rate of change is below the threshold *Test Not Completed *Test Not Completed This Monitoring Cycle C1A04-92 (50) Front right height sensor - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle C1A05-26 (50) Rear left height sensor - General signal failure - signal rate of change is below the threshold *Test Not Completed *Test Not Completed This Monitoring Cycle C1A05-92 (50) Rear left height sensor - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle C1A06-26 (50) Rear right height sensor - General signal failure - signal rate of change is below the threshold *Test Not Completed *Test Not Completed This Monitoring Cycle U0133-87 (50) Lost communication with dynamic response module - Bus signal/message failure - missing a message *Test Not Completed *Test Not Completed This Monitoring Cycle C1123-1C (50) Steering isolation valve supply circuit - General electrical failure - circuit voltage out of range *Test Not Completed *Test Not Completed This Monitoring Cycle C1A06-92 (50) Rear right height sensor - Component failure - performance or incorrect operation *Test Not Completed *Test Not Completed This Monitoring Cycle C1B18-62 (50) Supply voltage x-ref check - Algorithm based failure - signal compare failure *Test Not Completed *Test Not Completed This Monitoring Cycle C1A07-62 (50) Cross articulation - Algorithm based failure - signal compare failure *Test Not Completed *Test Not Completed This Monitoring Cycle C1A20-64 (50) Pressure increases too slow when filling reservoir - Algorithm based failure - signal plausibility failure *Test Not Completed *Test Not Completed This Monitoring Cycle U0136-87 (50) Lost communication with differential control module - rear - Bus signal/message failure - missing a message *Test Not Completed *Test Not Completed This Monitoring Cycle C1A55-01 (50) Ignition switch input circuit - General failure information - general electrical failure *Test Not Completed *Test Not Completed This Monitoring Cycle U1A14-49 (50) CAN initialisation failure - System internal failure - internal electronic failure *Test Not Completed *Test Not Completed This Monitoring Cycle U2000-67 (50) Motor temperature - Algorithm based failure - signal is incorrect after the event *Test Not Completed *Test Not Completed This Monitoring Cycle C1A00-1C (50) Control module - General electrical failure - circuit voltage out of range *Test Not Completed *Test Not Completed This Monitoring Cycle C1122-01 (50) Steering isolation valve - General failure information - general electrical failure *Test Not Completed *Test Not Completed This Monitoring Cycle C1130-7A (50) Air spring air supply - Mechanical failure - fluid leak or seal failure *Test Not Completed *Test Not Completed This Monitoring Cycle C112F-72 (50) Air spring valve - Mechanical failure - actuator is stuck open *Test Not Completed *Test Not Completed This Monitoring Cycle C1130-66 (50) Air spring air supply - Algorithm based failure - signal has too many transitions/events *Test Not Completed *Test Not Completed This Monitoring Cycle U0434-86 (50) Invalid data received from dynamic response module - Bus signal/message failure - signal is invalid *Test Not Completed *Test Not Completed This Monitoring Cycle C1139-23 (50) Unknown *Test Not Completed *Test Not Completed This Monitoring Cycle C1138-23 (50) Access switch - General signal failure - signal stays low *Test Not Completed *Test Not Completed This Monitoring Cycle C113A-64 (50) Wake-up control - Algorithm based failure - signal plausibility failure *Test Not Completed *Test Not Completed This Monitoring Cycle Ventilation B1A70-01 (50) Compressor solenoid positive supply - General failure information - general electrical failure *Test Not Completed *Test Not Completed This Monitoring Cycle B1A73-18 (50) Left seat heater - General electrical failure - circuit current below threshold *Test Not Completed *Test Not Completed This Monitoring Cycle B1A74-18 (50) Right seat heater - General electrical failure - circuit current below threshold *Test Not Completed *Test Not Completed This Monitoring Cycle B1B65-15 (2F) Left seat heater temperature sensor - General electrical failure - circuit short to battery or open ( at 221224 km ) *Test Failed *Test Failed This Monitoring Cycle *Confirmed *Test Failed Since Last Clear B1B66-15 (2F) Right seat heater temperature sensor - General electrical failure - circuit short to battery or open ( at 221224 km ) *Test Failed *Test Failed This Monitoring Cycle *Confirmed *Test Failed Since Last Clear

Jeg må antagelig bytte/fixe innslaget på startmotoren. Startmotoren går rundt, men tannhjulene griper ikke ordentlig inn i hverandre (?) så det blir et fryktelig rabalder. Vil et "solenoid starter motor repair kit" også fixe at tannhjuet slår inn, eller må jeg kjøpe et ekstra kit for dette problemet?

Har noen små deler for salg, sett med hengsler til dører forran til defender, panser og vindus hengsler. Forskjermer, har vært gjennom litt, små bulket og små hull i. Så en fullt fungerende startmotor til td5 motor. Kom med bud. Alt kan sendes. 90826132 Kent

Når eg vrir om nøkkelen startar motoren, men det kjem ein lyd som tyder på at drevet (er det det dei kallar bendix?) ikkje vil fly unna startkransen igjen når jobben er gjort. Det er snakk om ein 300 tdi som er gått 200 000 km. Har noen vert borti tilsvarande? Korleis reparerer ein det? Eg har aldri overhalt startmotor før, men det er jo laga av folk, så da må det vel kunne reparerast av folk. Ny er dyr.

Hei fikk plutselig problemer med å starte freelanderen igår. Heldigvis hadde jeg i all uflaks parkert i en bakke så jeg fikk trillet den igang og kom meg på jobb. Målte batteri med voltmeter før jeg prøvde å trillestarte og hadde 12,54 volt Og når jeg da hadde fått startet den på denne måten tok jeg å målte hvor mye dynamo ga på batteri den ga ca 14,4 volt. Utfra disse målninger konkluderer jeg med at dynamo er ok og det samme med batteri. Har også lest litt om mulige omtalte feil her på forum. Roy tror jeg nevnte noe om at mulig jordingsfeil fra minuspol til karosseri og en annen nevnte noe om at motorblokka ikke var jordet til karosseri og når han gjorde det var startproblemer borte. Prøvde dette igår kveld Brukte startkabel fra minuspol til karosseri gods for å evt sjekke om det var dårlig jording fra minuspol. Vil ikke starte Prøvde deretter å jorde motorblokka til karosseri med samme startkabel. Starter ikke. Er ikke veldig god på det bilelektriske så trenger litt eksperthjelp av forumet. Bør jeg prøve begge jordingsmetoder over samtidig eller er det fare ved å gjøre det? Gikk så over alle ledninger fra batteri til jord etc for å se om det var noe irring noe sted eller løse ledninger. Jeg fant en lednig som ikke så helt bra ut da den var teipet og teipen hadde løsnet. Ledningen gikk til fuel injection pump og var sort og hvitt på farge. Jeg prøver å legge med bilde av den. Ledningen har en gang vært delt i to og så surret sammen. Jeg hadde en sukkerbit (hvit på bilde) liggendes i verktøykassa som jeg monterte i håp om å oppnå bedre kontakt. Noen som vet funksjonen til denne ledning? Er det jording av fuel inction pumpa? Og hvis den ledning ikke er helt god kan det forårsake at man ikke får start? Etterpå så jeg også en ledning som var uisolert som også kan sees på bilde 1 over. Den ligger til venstre for rør inntill fuel injection pump. Legger med et bilde til av uisolert ledning. Den ligger ved siden av de to ledninger som er sort og brun/rød som går til den oransjebrune kontakt til venstre i bildet. Noen som vet om det skal gå 3 ledninger inn i denne kontakt evt hvor denne uisolerte ledning skulle ha vært? Jeg mistenker at det er starter som er gåen eller solenoidene i starter som er slitt. Leste et sted at de burde byttes hver 100 000 miles. Tenkte jeg skulle sjekke ut dette imorgen og gjøre litt research idag. Fikk tak i freelander haynes boka idag og har lest litt i den og der står det følgende: ad feilsøking kapittel 5 avsnitt 9 starting system ok pkt 5 feilsøking på solenoider The solenoid contacts can be checked by connecting a voltmeter or test lamp between the battery positive feed connection on the starter side of the solenoid, and earth. when the ignition switch is turned to the 'start' position, there should be a reading or lighted bulb, as applicable. If there is no reading or lighted bulb, the solenoid is faulty and should be renewed. Hvis jeg har forstått rett så måler jeg da fra under rødt kontaktpkt på starter altså solenoid og karosseri jord. Og får samtidig da en til å vri om tenning til start inne i bilen og får jeg da utslag så er det ikke noe feil med solenoidene, men mest sannsynlig noe annet galt med starter. Holder det å måle i volt på voltmeter eller må jeg ha en annen innstilling ohm ampere etc? Vuderer et sånn solenoidrepsett til starter noen som har noe erfaring med disse repsettene? Hvis solenoidene er ok tenkte jeg evt å få tak i en ny starter på evt reservedeler24.co.no/stark-7491997.html har noen noe erfaringer med dette firmaet? All hjelp, råd og tips mottas med stor takk!

Fikk et problem i dag med familiebilen: Da jeg skulle starte vår Suzuki Grand vitara, så begynte startmotoren å dra litt rundt, men så stopper den. Slo av tenningen... Gjorde et nytt forsøk, men da høres det ut som den bare sviver rundt i stor fart, men trekker ikke i gang motoren.... Trenger tips og råd.... Hjelp! :-/

Har igjen problemer med startmotoren i exmilen. Den ville ikke starte her for en stund siden. Starmotoren gikk men den tok ikke med seg motoren rundt. Tenkte det bare var det tannhjulet som går innpå svinghjulet som ikke ville være med i kulda. Prøvde med startsveiv og da rikket ikke motoren seg.. Prøvde å rikke bilen i gir og den hang på giret. Åpnet opp og fant dette:

Selger ny startmotor til defender 110 NAD 500210 Gi bud Espen Hana mob 90873109